Heath Zenith SL-9525 Manual do Utilizador descarregar pdf

Mode: On-Time: Works: Day Night

Test 5 Sec x x

Auto 1, 5, 10 min. x

Manual Until Dawn* x

OPERATION

* resets to Auto Mode at dawn.

MANUAL MODE

ON-TIME

10 5 1 TEST

ON-TIME

TEST

... back on.

AUTO

1 Second OFF

then...

Move ON-TIME Switch to

1, 5, or 10 minutes

Mode Switching Summary

Flip light switch off

for one second then

back on*

MANUAL MODE

AUTO

TEST

Requirements

• The Light Control requires 120-volts AC.

• If you want to use Manual Mode, the control must be

wired through a switch.

• Some codes require installation by a

qualified electrician.

• This product is intended for use with the enclosed

gasket and with a junction box marked for use in wet

locations.

Model SL-9525

Features

• Turns on lighting when motion is detected.

• Automatically turns lighting off.

• Photocell keeps the lighting off during daylight hours.

• LED indicates motion was sensed (day or night).

Motion Sensor Light

Control

* If you get confused while switching modes, turn the

power off for one minute, then back on. After the

calibration time the control will be in the AUTO mode.

Note: When first turned on wait about 1

minutes for

the circuitry to calibrate.

Gasket

4 Screws

(2 sizes included)

2 Flood Lamps

2 Wire

Connectors

This package includes:

Light Control

Sensor

Cover

Plate

Lamp Holders

2 Shells

Light Shield

As an ENERGY STAR

Partner, Heath

/Ze-

nith has determined that this product meets

the ENERGY STAR

guidelines for energy

efficiency. This product is ENERGY STAR

compliant when used with 120 Watt bulbs.

Manual mode only works at night

because daylight returns the sen-

sor to AUTO.

Flip the light switch off for one sec-

ond then back on to toggle between

AUTO and MANUAL MODE.

Manual mode works only with the

ON-TIME switch in the 1, 5, or 10

position.

Put the ON-TIME switch in the 1, 5,

or 10 minute position.

Put the ON-TIME switch on the

bottom of the sensor in the TEST

position.

1 2 3 4 5 6 ... 11 12

Resumo do Conteúdo

Página 1 - Motion Sensor Light

Página 2

10595-5612-08INSTALLATIONPour faciliter l’installation, choisir un appareil d’éclairagedevant être remplacé et qui est déjà commandé par uninterrupteu

Página 3 - SPECIFICATIONS

11595-5612-08ESSAIS ET RÉGLAGES❒ Mettre en circuit le disjoncteur et l’interrupteurd’éclairage.DétecteurLe détecteur est moins sensible au mouvement d

Página 4 - TROUBLESHOOTING GUIDE

12595-5612-08GUIDE DE DÉPANNAGESYMPTÔMEL’éclairage nes’allume pas.L’éclairages’allume en pleinjour.L’éclairages’allume sansraison apparente.CAUSE POSS

Página 5 - Control de luz del

2595-5612-08INSTALLATIONFor easy installation, select an existing light with a wallswitch for replacement.WIRE THE LIGHT CONTROL.❒ Twist the junction

Página 6 - INSTALACION

3595-5612-08MotionMotionTEST AND ADJUSTMENT❒ Turn on the circuit breaker and light switch.SensorThe detector is most sensitive to motion across its fi

Página 7 - ESPECIFICACIONES

4595-5612-08SYMPTOMLights will not comeon.Lights come onin daylight.Lights come on forno apparent rea-son.POSSIBLE CAUSE1. Light switch is turned off.

Página 8 - SERVICIO TÉCNICO

5595-5612-08Modalidad: tiempo encendido Trabaja: Día NochePrueba 5 seg. x xAutom. 1, 5 ó 10 min. xManual Hasta el xamanecer*FUNCIONAMIENTO*Se pone en

Página 9 - Commande d’éclairage à

6595-5612-08Para una fácil instalación escoja una luz con uninterruptor de pared.Montaje en pared Montaje en aleroINSTALACION❒ Conecte los cables de l

Página 10 - INSTALLATION

7595-5612-08PRUEBA Y AJUSTE❒ Prenda el cortacircuitos y el interruptor de luz.TornilloSujetadorUniónEsféricaApunte eldetector haciaabajo para pocacobe

Página 11 - FICHE TECHNIQUE

8595-5612-08GUIA DE INVESTIGACION DE AVERIASSINTOMALa Luz no seenciende.La luz se prendedurante el día.La luz se prende sinninguna razónaparente.POSIB

Página 12 - SERVICE TECHNIQUE